Refrigerator repair
Fridge side warming, freezer iced over, a Sub-Zero built-in misbehaving, or a unit laid flat for a move? We meter defrost, fan and sealed-system parts, then quote in writing.

Appliance repair · Kitsap Peninsula and Gig Harbor
Appliances on this side of the water put up with long damp winters, wells that carry grit, windstorm outages that end in a surge, and moving days that tip refrigerators onto their backs. Our technicians repair cold storage, laundry machines, dishwashers and cooking equipment across Bremerton, Silverdale, Poulsbo, Gig Harbor and Fox Island.
Straight to it
Larch HVAC & Appliance fixes household machines across Bremerton, Silverdale, Poulsbo, Gig Harbor and Fox Island: fridges and freezers, ice makers, washing machines and dryers, dishwashers, plus ranges, wall ovens and cooktops. Washington lists this work as 07D Appliance Repair, a specialty tied to license LARCHHA742PL, our electrical contractor registration. Each suspect part is metered, the repair gets priced on paper, and work waits for your approval.
Every machine has a few parts behind most of its breakdowns, and our technicians meter those first rather than guessing with new parts.

Fridge side warming, freezer iced over, a Sub-Zero built-in misbehaving, or a unit laid flat for a move? We meter defrost, fan and sealed-system parts, then quote in writing.
Front-loader smelling sour, a fill slowed by well grit, standing water, or a washer that hops after a move? We test pump, valve, lock and suspension, then quote.
Clothes still damp after two cycles, no heat at all, a squealing drum, or a gas dryer that glows but never lights? We test fuses, elements, igniters and belts, then quote.
Standing water, a fill that never finishes, cloudy glasses, wet plates or a latch that won't catch? We meter pumps, valves, heaters and boards, then put the price in writing.
Oven dawdling to temperature, a burner ticking without flame, a self-clean door locked tight, or a Wolf range misbehaving? We test igniters, elements and sensors, then quote.
No ice, hollow cubes, a fill tube frozen in a cold garage, or a built-in ice maker gone quiet? We test the inlet valve, module and fill path, then quote the fix in writing.
Water first. Bremerton mixes surface water from the Union River watershed with city wells, so hardness spans roughly 32 to 98 mg/L, soft to moderately hard; the softness mostly shows up as detergent overdosing and film. Silverdale, Poulsbo and Gig Harbor drink groundwater delivered by local districts or the city. On Fox Island and across rural ground near Poulsbo and Gig Harbor, many households pump from their own well or a small shared one, and sediment and iron clog the inlet screens on laundry machines, dishwashers and ice makers sooner.
Weather and moves come next. About 57 inches of precipitation a year in Bremerton keeps laundry rooms humid, so front-load boots sprout mildew and dryers run long. Windstorms send fir, cedar and alder into power lines, and the November 2024 bomb cyclone darkened much of the region; restoration surges are rough on control boards. Households here move often, too, and arrive with a fridge that rode on its back or a front-loader that skipped its shipping bolts.
Each tab holds a photo from our service calls and a note on what we check first. Pick any tab; left alone, they turn every few seconds.

Tab 1 of 12
Sealed-system work, from leak search to recharge, happens right in the kitchen under EPA 608 Universal credentials, so the fridge stays where it stands.
See the service page
Tab 2 of 12
Damp Kitsap laundry rooms are hard on door boots, so mildew, torn folds and a clogged pump filter are the first things we look at on a front-loader.
See the service page
Tab 3 of 12
Long vent runs through damp walls fill with lint quickly, so the vent gets tested along with the heating side: element or burner, thermal fuse and thermostats.
See the service page
Tab 4 of 12
Well water leaves minerals on the spray arms and the inlet screen, two early stops when dishes come out dull or the tub fills slowly.
See the service page
Tab 5 of 12
Natural gas and propane ranges both get igniter, valve and flame checks. The tank and its lines stay with your propane supplier.
See the service page
Tab 6 of 12
After a windstorm outage the fill tube often freezes solid and the ice maker goes quiet, so we follow the water up from the inlet valve.
See the service page
Tab 7 of 12
Through the gray months we watch the defrost cycle closely, because a coil that never clears is the classic Kitsap winter call. Capacitors and the reversing valve come next.
See the service page
Tab 8 of 12
More Kitsap homes have cooling since the 2021 heat dome. When a system falls behind on a hot afternoon, we start with airflow, the capacitor and the refrigerant charge.
See the service page
Tab 9 of 12
Many older Bremerton and Manette houses keep the furnace in a closet or under the floor. Filter, inducer, flame sensor and limit switch all get checked in that tight space.
See the service page
Tab 10 of 12
Placement matters on the peninsula: a raised pad clear of wet ground, back from salt spray where the lot allows, and out from under the needle drop.
See the service page
Tab 11 of 12
Mini-splits fit older homes with no room for ducts. Their line sets need sound insulation where they cross a damp crawlspace, and the outdoor unit needs a clear drain path.
See the service page
Tab 12 of 12
A seasonal visit near the water means a coil rinse, a look at the fasteners for salt rust and a base pan that drains. Those three buy waterfront equipment years.
See the service pageOn paper, before any work. The diagnostic visit carries a fee, named by the office as you schedule. A yes to the repair credits that fee toward the total; a no makes it the visit's single charge. Fan motors, valves, belts, pumps, igniters, thermal fuses and door switches usually travel on the truck, and anything ordered is priced before the order. Each invoice states our warranty terms in writing.
Repair tends to win when a single component has failed while the cabinet, drum or sealed system around it remains healthy. If a quote creeps toward what a replacement would run, as it can with a seized compressor or a worn-out tub bearing, the technician tells you so plainly and you make the call.
Yes. Our appliance technicians work in Bremerton, Silverdale, Poulsbo, Gig Harbor and Fox Island, including Artondale, Wollochet, Rosedale, Purdy and Canterwood near Gig Harbor. Island visits are planned around the single bridge over Hale Passage, so read the appliance's model number to the office when you book; so the probable parts make the first crossing with the technician.
Our list runs from everyday names, GE, Kenmore, LG, Maytag, Whirlpool, Frigidaire and Electrolux, to Bosch and KitchenAid kitchens, Speed Queen laundry, and Sub-Zero, Wolf and Thermador built-in and pro-style equipment. We also handle Samsung laundry machines, ranges and dishwashers. The model and serial sticker tends to sit inside a door, beneath a lid or on the rear; reading it out at booking lets the technician bring matching parts.
Yes. When power returns after a windstorm, the surge tends to hit control boards, display boards and relays rather than motors or compressors. Our technician tests supply at the appliance first, then the board's outputs, and quotes a board only when the readings show it failed. To protect appliances next time, unplug them during the outage and reconnect a few minutes after power steadies.
No. Our appliance work is repair: diagnosing and replacing failed parts in machines you already own, from the fridge to the dryer. Running gas or water lines, fuel conversions and electrical changes at the wall are outside our scope, and we'll say so when a problem starts there. Inside the appliance, from inlet valve to control board, is where we work.
Talk to a person
Our booking page asks for just a date and an arrival window; phone callers reach a live person between 8 AM and 7 PM, all week. Once the office has confirmed with a call, your technician phones while underway.
Schedule online
Tell us what needs attention, the day that works and the window you prefer. A scheduler calls to make it firm, and the technician rings again before pulling up.
Washington Labor & Industries keeps these records public. Each number can be searched on L&I Verify; scope details sit on a separate page.
Scope of each license