
Tab 1 of 12
Heat pump repair
Through the gray months we watch the defrost cycle closely, because a coil that never clears is the classic Kitsap winter call. Capacitors and the reversing valve come next.
See the service page
FAQ · Peninsula and harbor homes
Quick answers about getting a technician to the door, what lands on paper before any work, and how rain, salt spray, wind and well water treat equipment on this side of the Sound. Missing something? Phone the office; the line opens at 8 AM and stays staffed until 7 PM, every day.
The questions that come up most from Bremerton, Silverdale, Poulsbo, Gig Harbor and Fox Island: how booking and the fee work, what goes in writing, which places and brands we cover, and what local weather and water do to heat pumps, furnaces and appliances. Each reply leads with the short version, whether home is a Charleston bungalow a few blocks from Sinclair Inlet, a newer house on the hills above Poulsbo or a view lot on Fox Island.
Online or by phone, whichever you like. The booking page wants two picks from you, a date and an arrival window, after which the office rings to make it firm. Prefer conversation? A person staffs the line each day from 8 AM, with the last call taken at 7. When visit day comes, your technician calls on leaving for your street. A model number and a one-line note on the trouble, ready in advance, speed everything up.
Yes. Diagnosis is its own paid visit, and the amount comes from the office as part of scheduling. After testing, the technician puts the repair cost on paper and leaves the choice with you. Agree, and the diagnostic fee becomes part of what that repair costs. Decline, and you're billed for diagnosis alone. Work waits for your yes, and an ordered part shows its cost on that same paper estimate.
Whatever your invoice states, because the terms are written there beside the parts installed and the work done. Coverage for one replaced part may differ from coverage on a full system, so read the terms attached to your job. If the same fault resurfaces while they still apply, call us, refer to the earlier visit and keep the invoice within reach; the return trip follows those written terms.
Bremerton (98310, 98311, 98312, 98314, 98337), Silverdale (98383, 98315), Poulsbo (98370), Gig Harbor (98332, 98335, 98329) and Fox Island (98333). The island is reached only by its bridge over Hale Passage from Artondale, so island calls are planned around that crossing, and East Bremerton stops are routed over the Manette or Warren Avenue bridge. Close to the edge of those ZIP codes? Ask the office.
Nearly everything installed around here. For comfort systems: Daikin, Fujitsu and Mitsubishi ductless units, plus Lennox, Trane, York, Carrier, Goodman, Bryant, LG and Rheem/Ruud ducted equipment. For appliances: Bosch, Whirlpool, GE, Frigidaire, Maytag, LG, Kenmore, KitchenAid, Electrolux, Sub-Zero, Speed Queen, Thermador and Wolf, and Samsung ranges, dishwashers, washers and dryers. Sharing the make and model at booking lets the technician bring the right service information.
You are watching a defrost cycle, and on the peninsula they come often. Air between 35 and 50°F is wet enough to coat the outdoor coil in frost, and the board answers by reversing refrigerant flow for a few minutes: the fan halts, the coil warms, frost melts and lifts away as vapor, and the reversing valve shifts back with a whoosh. Call if ice still coats the coil once the fan restarts.
Not necessarily. AUX means the backup heat strips inside the air handler are switched on. Brief spells during a defrost or a frosty dawn are normal. It deserves a closer look when the light glows for hours through mild, wet 45-degree weather, a sign the heat pump has likely stopped contributing and the strips are heating the house alone. Running on strips alone drives up the power bill, so get a visit booked soon.
Probably not entirely, and that reflects design rather than a defect. Systems here are sized for summers that peak around 77–78°F, so on June 28, 2021, when Bremerton touched 110°F, even healthy units ran flat out and still lost ground. A weak run capacitor, matted condenser fins or a short refrigerant charge widens that gap. A spring check of temperature split, superheat and subcooling separates normal limits from real faults.
Look at the thermostat first; a blank screen may want batteries or a reboot. Many heat pumps pause several minutes before restarting, so allow some time. If nothing runs, see whether a breaker has tripped, and flip it back on once and only once. If it trips again, or the equipment flashes an error, clicks without starting or smells scorched, book a visit, because the surge when service returns often damages control and defrost boards.
Yes, slowly. Spray drifting off Sinclair or Dyes Inlet, Liberty Bay, the harbor or Hale Passage settles on the coil and cabinet, and over the years fins turn powdery, screws rust and contactor terminals corrode. With the thermostat off and the breaker switched off, a gentle garden-hose rinse with fresh water a few times a year helps. Keep pressure washers away, and ask about coated coils when replacing a unit near the shore.
It can. Bremerton blends well water measuring 56–98 mg/L of hardness (3.3–5.7 grains per gallon) with softer surface water from the Union River watershed at about 32 mg/L. Silverdale, Poulsbo and Gig Harbor rely mostly on groundwater, and Fox Island homes often sit on private or community wells. Sediment, iron and minerals clog washer and dishwasher inlet screens and the valve feeding an ice maker, so fills slow and ice production stalls.
Get out first; questions can wait. Lead everyone outside, then from a safe distance call 911 or whoever supplies your gas or propane. On the way, leave switches, the thermostat and any flame alone. Once the supplier or fire crew clears the house, our technicians can check the gas valve, the igniter, the burners and the inducer with its pressure switch, then write up a repair price before touching anything.
Talk to a person
Call the office any day once it opens at 8 AM and until it closes at 7 PM, or reserve a slot through online booking and bring the question up when the office rings to confirm.
Each tab holds a photo from our service calls and a note on what we check first. Pick any tab; left alone, they turn every few seconds.

Tab 1 of 12
Through the gray months we watch the defrost cycle closely, because a coil that never clears is the classic Kitsap winter call. Capacitors and the reversing valve come next.
See the service page
Tab 2 of 12
More Kitsap homes have cooling since the 2021 heat dome. When a system falls behind on a hot afternoon, we start with airflow, the capacitor and the refrigerant charge.
See the service page
Tab 3 of 12
Many older Bremerton and Manette houses keep the furnace in a closet or under the floor. Filter, inducer, flame sensor and limit switch all get checked in that tight space.
See the service page
Tab 4 of 12
Placement matters on the peninsula: a raised pad clear of wet ground, back from salt spray where the lot allows, and out from under the needle drop.
See the service page
Tab 5 of 12
Mini-splits fit older homes with no room for ducts. Their line sets need sound insulation where they cross a damp crawlspace, and the outdoor unit needs a clear drain path.
See the service page
Tab 6 of 12
A seasonal visit near the water means a coil rinse, a look at the fasteners for salt rust and a base pan that drains. Those three buy waterfront equipment years.
See the service page
Tab 7 of 12
Sealed-system work, from leak search to recharge, happens right in the kitchen under EPA 608 Universal credentials, so the fridge stays where it stands.
See the service page
Tab 8 of 12
Damp Kitsap laundry rooms are hard on door boots, so mildew, torn folds and a clogged pump filter are the first things we look at on a front-loader.
See the service page
Tab 9 of 12
Long vent runs through damp walls fill with lint quickly, so the vent gets tested along with the heating side: element or burner, thermal fuse and thermostats.
See the service page
Tab 10 of 12
Well water leaves minerals on the spray arms and the inlet screen, two early stops when dishes come out dull or the tub fills slowly.
See the service page
Tab 11 of 12
Natural gas and propane ranges both get igniter, valve and flame checks. The tank and its lines stay with your propane supplier.
See the service page
Tab 12 of 12
After a windstorm outage the fill tube often freezes solid and the ice maker goes quiet, so we follow the water up from the inlet valve.
See the service pageSchedule online
Tell us what needs attention, the day that works and the window you prefer. A scheduler calls to make it firm, and the technician rings again before pulling up.
Washington Labor & Industries keeps these records public. Each number can be searched on L&I Verify; scope details sit on a separate page.
Scope of each license