Jump to main content
Bremerton · Silverdale · Poulsbo · Gig Harbor · Fox IslandLive answer daily, 8 AM until 7 PM
LarchHVAC & Appliance (360) 728-3833
Older condenser under test with hoses and a gauge set attached

Heating and cooling

Heating & Cooling Repair in Bremerton, Silverdale & Poulsbo, WA

Larch keeps peninsula homes comfortable through soggy winters and the odd blistering week. We fix, service and install heat pumps, central air, furnaces and ductless systems from Bremerton to Fox Island. Repairs are priced on paper, and the tools stay packed until you approve.

  • Trip charge, then creditedExpect the diagnostic charge to be spelled out on the booking call. Green-light the fix and it is credited against the job; skip the fix and that single visit is all you owe.
  • Cost on paper, your decisionTesting pinpoints the fault, a written number follows, and nothing comes apart until you nod.
  • Coverage in writingEvery finished repair carries its warranty terms printed on your invoice.

Straight to it

Larch handles the heating and cooling systems found in Bremerton, Silverdale, Poulsbo, Gig Harbor and Fox Island homes: heat pumps with or without ducts, central air, heat-strip air handlers, and gas, propane or electric furnaces. We repair them, tune them and install new ones. Licensing covers it: the 06A HVAC/Refrigeration specialty, a General contractor registration, and EPA 608 Universal for refrigerant. Prices come in writing before work, and each invoice states the warranty.

What heating and cooling work do our technicians handle?

Repair, seasonal service and installation for the equipment Kitsap houses actually rely on: ducted heat pumps, ductless mini-splits, central air, electric furnaces and heat-strip air handlers, gas furnaces on streets with gas service, and propane furnaces in some rural homes. Daikin, Carrier, Mitsubishi, Trane, Fujitsu, Lennox, LG, Goodman, Bryant, Rheem, Ruud and York all turn up on our calls. Each service has a page of its own:

  • Heat pump repair: reversing valves that stick, defrost boards and coil thermistors that misjudge frost, salt-crusted contactors, needle-clogged base pans, and AUX strips that run when they should rest.
  • Air conditioner repair: capacitors weakened by months of idleness, seized condenser fans, pinhole leaks, iced evaporator coils and algae-filled condensate traps.
  • Furnace repair: gas and propane burners that will not light or stay lit, electric elements and sequencers that burn out, blowers that quit. Oil equipment is outside our work.
  • Ductless mini-splits: dripping or musty heads, blinking fault codes, failed condensate pumps, board faults and flare-nut leaks, plus new single-zone and multi-zone systems.
  • HVAC tune-ups: coil cleaning, salt rinses near the water, capacitor and contactor checks, superheat, subcooling, static pressure, flame-sensor microamps and a forced defrost.
  • Heat pump and AC installation: load-calculated sizing, coastal coil options, raised pads, and one quoted number for the equipment and the install.
  • Thermostats: new controls and the low-voltage wiring behind them, set up correctly for heat pump O/B and auxiliary heat lockout.
Gas furnace burner compartment open for igniter service

Heat pumps, furnaces and cooling

Heat pump repair

Ice that will not clear, steam clouds all afternoon, an AUX light that never rests. We test defrost boards, coil sensors, capacitors and salt-worn parts on Kitsap heat pumps.

Air conditioner repair

An AC that napped since last September and quits on the first scorching afternoon. We chase down tired capacitors, burned contactors, seized fan motors, slow leaks and iced coils.

Furnace repair

Electric furnace tripping its limit, gas furnace locking out, propane unit refusing to light. We repair igniters, flame sensors, sequencers, elements and blowers across Kitsap.

Heat pump & AC installation

New heat pumps, central air and air handlers sized room by room, with coastal coil options for waterfront lots and a written quote stating one figure for everything.

Ductless mini-splits

Heads that drip, smell musty or flash error codes, plus new ductless systems for baseboard homes, view rooms, ADUs and shops across Kitsap and on Fox Island.

HVAC tune-ups

Spring and fall tune-ups that log real numbers, from capacitor microfarads and flame-sensor microamps to static pressure and superheat, plus a forced defrost and a salt rinse for waterfront coils.

What does the Kitsap climate do to heating and cooling equipment?

Mostly it soaks it and runs it hard. Bremerton averages about 57 inches of precipitation a year, more than the city across the Sound, so outdoor coils seldom dry out between fall and late spring. Moss and fir needles collect in cabinets, alder catkins clog base pans, condensate drains grow algae, and crawlspace furnaces and ducts sit in damp air all winter. Heat pumps here often run daily from October into May, defrosting again and again in 35-to-50-degree drizzle, so their contactors, capacitors and reversing valves age by cycles rather than by calendar years.

Then come the jolts. Windstorms topple firs and alders onto power lines; the November 2024 bomb cyclone closed 22 Kitsap County roads and cut power across the region, and surges on restoration damage control boards, capacitors and contactors. Summer is usually mild, yet on June 28, 2021 Bremerton set its all-time record of 110°F, so air conditioners that idle for most of the year must be ready for a week of extremes. Near Sinclair and Dyes Inlets, Liberty Bay, the harbor and Hale Passage, salt air adds steady corrosion to coils, screws and electrical terminals.

Seasonal tune-ups stay ahead of most of this. A spring visit cleans and rinses the outdoor coil, reads the capacitor and contactor, checks charge and static pressure, and flushes the drain before the first hot spell. A fall visit forces a heat pump through defrost, tests the backup strips, and on gas or propane furnaces measures flame-sensor microamps and checks the igniter, inducer and venting before the long wet season.

Twelve tabs, one for each kind of job

Each tab holds a photo from our service calls and a note on what we check first. Pick any tab; left alone, they turn every few seconds.

Heat pump outdoor unit with a digital gauge set during a refrigerant charge

Tab 1 of 12

Heat pump repair

Through the gray months we watch the defrost cycle closely, because a coil that never clears is the classic Kitsap winter call. Capacitors and the reversing valve come next.

See the service page
1 / 12

How do we help you choose between repair and replacement?

Repair comes first in our thinking, since a healthy system with a single bad part rarely needs replacing. The technician writes down what broke, what the fix costs and anything else worth keeping an eye on, such as an oily stain at a brazed joint, a capacitor drifting low or a coil corroding near the water. When replacement is the smarter path, you also get a written quote for new equipment with the installation included in a single number, prepared under our General contractor license.

Older homes on Bremerton's west side and in Manette often run on baseboard or retrofitted heat pumps, two-story houses in Silverdale subdivisions and the Gig Harbor uplands tend to have warm upstairs bonus rooms, and many households across the peninsula have added a heat pump or ductless system since 2021. Whatever your house has, the first step is the same: a diagnostic or measuring visit, booked online or by phone.

What Kitsap homeowners ask us

Do you come out to Fox Island and the Gig Harbor area?

Yes. Along with Bremerton, Silverdale and Poulsbo, we serve Gig Harbor and nearby communities such as Purdy, Rosedale, Artondale, Wollochet and Canterwood, plus Fox Island. Island visits are planned around the single bridge across Hale Passage, and the office confirms your appointment by phone so the timing works for both sides.

How does the diagnostic fee work?

Think of it as the price of finding the fault: a fixed diagnostic fee, which the office states before anyone is dispatched. Approving the repair means the fee is not added on, because it already sits within the repair total. Declining means you pay only the fee, and the written estimate is yours to keep.

Do you work on oil furnaces or propane tanks?

No to both. We repair heat pumps, ductless systems, air handlers, central AC and furnaces that run on gas, propane or electricity, but oil furnaces, oil tanks and propane tank work are outside our scope. On a propane home we fix the furnace itself, while the tank, regulator and supply line stay with your propane supplier.

My house has no ducts. Can I still get air conditioning?

Yes, most often with a ductless mini-split. A compact outdoor unit feeds one or several heads mounted high on the walls through a narrow refrigerant line set, so rooms get efficient heat and cooling with no ducts built, and existing baseboards can stay as backup. We flag electrical work beyond our scope before pricing, and the quote shows the whole job as one number.

Talk to a person

Book heating or cooling service on the peninsula

Use the website to claim a date and the arrival window that suits you, or call between the 8 AM opening and the 7 PM close on any day. Every booking gets a confirming call from our office.

Schedule online

Three screens, then a confirming call

Tell us what needs attention, the day that works and the window you prefer. A scheduler calls to make it firm, and the technician rings again before pulling up.

  • Diagnostic named on the call, credited toward any repair you okay.
  • Common wear parts ride along, which often means one trip does it. Anything we must order is quoted to you first.
  • Bridges and islands are fine: add directions or gate notes in the problem box.

(360) 728-3833

Schedule a service visit

Pick the equipment, a day and a window. A scheduler calls to confirm before anything is final.

What needs a look
Day & details
Which day
Arrival window
Contact

The diagnostic charge is stated when we call and credited toward any repair you approve. We use these details only to set up the visit.

State licenses you can look up

Washington Labor & Industries keeps these records public. Each number can be searched on L&I Verify; scope details sit on a separate page.

Scope of each license
CallSchedule