Jump to main content
Bremerton · Silverdale · Poulsbo · Gig Harbor · Fox IslandLive answer daily, 8 AM until 7 PM
LarchHVAC & Appliance (360) 728-3833
Heat pump outdoor unit with a digital gauge set during a refrigerant charge

Bremerton · Silverdale · Poulsbo · Gig Harbor · Fox Island

Heating, Cooling & Appliance Repair in Bremerton, Silverdale & Poulsbo, WA

Larch HVAC & Appliance looks after the peninsula's heat pumps, furnaces, mini-splits and air conditioners, plus the fridge, range, dishwasher and laundry machines that live under the same roof. Tell the booking page which date works and which arrival slot you prefer, and the office rings back to settle it.

  • Trip charge, then creditedExpect the diagnostic charge to be spelled out on the booking call. Green-light the fix and it is credited against the job; skip the fix and that single visit is all you owe.
  • Cost on paper, your decisionTesting pinpoints the fault, a written number follows, and nothing comes apart until you nod.
  • Coverage in writingEvery finished repair carries its warranty terms printed on your invoice.

Straight to it

Larch HVAC & Appliance is a licensed, independent Washington company. Our technicians fix and install heat pumps, central air, furnaces and ductless mini-splits, and they also mend dryers, dishwashers, refrigerators, ranges, ice makers and washers across Bremerton, Silverdale, Poulsbo, Gig Harbor and Fox Island. A person answers our line daily, 8 AM to 7 PM. Every repair is quoted in writing, and no part comes off the truck until you agree.

Heat pumps, furnaces and cooling

Diagnosis and repair for the systems that run nine months a year here, plus installs when a repair no longer makes sense.

Heat pump repair

Ice that will not clear, steam clouds all afternoon, an AUX light that never rests. We test defrost boards, coil sensors, capacitors and salt-worn parts on Kitsap heat pumps.

Air conditioner repair

An AC that napped since last September and quits on the first scorching afternoon. We chase down tired capacitors, burned contactors, seized fan motors, slow leaks and iced coils.

Furnace repair

Electric furnace tripping its limit, gas furnace locking out, propane unit refusing to light. We repair igniters, flame sensors, sequencers, elements and blowers across Kitsap.

Heat pump & AC installation

New heat pumps, central air and air handlers sized room by room, with coastal coil options for waterfront lots and a written quote stating one figure for everything.

Ductless mini-splits

Heads that drip, smell musty or flash error codes, plus new ductless systems for baseboard homes, view rooms, ADUs and shops across Kitsap and on Fox Island.

HVAC tune-ups

Spring and fall tune-ups that log real numbers, from capacitor microfarads and flame-sensor microamps to static pressure and superheat, plus a forced defrost and a salt rinse for waterfront coils.

All heating and cooling

Why does Kitsap and Gig Harbor weather wear out equipment?

Rain, salt, wind and the odd scorcher each take their cut. Bremerton's gauge averages about 57 inches of rain and other precipitation a year, and this side of the Sound is soggier than the big cities on the east shore, which sit partly in the Olympic rain shadow. December through February lows hover near 35°F, and the gray weeks on either side park between 35 and 50°F. Heat pumps love that band for efficiency, but saturated air keeps frosting the outdoor coil, so the defrost board, the reversing valve, the condenser fan motor and its run capacitor stack up far more cycles than they would on the dry side of the mountains. Moss, fir needles and alder catkins wedge into the fins and the base pan, holding water against aluminum and choking airflow.

Living near the water brings two more headaches. Houses facing Sinclair Inlet, Dyes Inlet, Liberty Bay, the harbor at Gig Harbor or Hale Passage catch salt spray that chews on coil fins, cabinet screws and contactor terminals. Below the floor, plenty of older homes tuck ducts and an air handler into a clammy crawlspace, where blower housings rust and duct seams sweat. Silverdale, Poulsbo and Gig Harbor drink mostly groundwater, and Fox Island plus much of the rural acreage runs on private or shared wells, so grit, iron and dissolved minerals reach washer and dishwasher inlet screens and the solenoid valve feeding a refrigerator.

Wind and heat are rare, yet they hit hard. Douglas fir, cedar, alder and maple crowd nearly every road out here, and big blows lay them across power lines; in the bomb cyclone that roared through on November 19–20, 2024, 22 Kitsap County roads were shut by fallen trunks or wires. The jolt when service comes back is rough on furnace boards, defrost controls and appliance electronics. Summer usually tops out around 77–78°F, so lots of houses never got central air, and then June 28, 2021 pushed Bremerton to 110°F, an all-time high. Cooling equipment that naps through most of the year suddenly ran for days straight, and weak capacitors and pitted contactors gave out in a cluster. Sound familiar? Get a visit on the calendar and let measurements steer the next move.

Dryer with the front panel off and the drum exposed

Kitchen and laundry appliances

Refrigerators, washers, dryers, dishwashers, ranges and ice makers, repaired in place.

Refrigerator repair

Fridge side warming, freezer iced over, a Sub-Zero built-in misbehaving, or a unit laid flat for a move? We meter defrost, fan and sealed-system parts, then quote in writing.

Washer repair

Front-loader smelling sour, a fill slowed by well grit, standing water, or a washer that hops after a move? We test pump, valve, lock and suspension, then quote.

Dryer repair

Clothes still damp after two cycles, no heat at all, a squealing drum, or a gas dryer that glows but never lights? We test fuses, elements, igniters and belts, then quote.

Dishwasher repair

Standing water, a fill that never finishes, cloudy glasses, wet plates or a latch that won't catch? We meter pumps, valves, heaters and boards, then put the price in writing.

Oven & range repair

Oven dawdling to temperature, a burner ticking without flame, a self-clean door locked tight, or a Wolf range misbehaving? We test igniters, elements and sensors, then quote.

Ice maker repair

No ice, hollow cubes, a fill tube frozen in a cold garage, or a built-in ice maker gone quiet? We test the inlet valve, module and fill path, then quote the fix in writing.

All appliance repair

What happens after you book?

Two phone calls come before the doorbell. Whether you reserve online or by calling, the office phones to make the appointment official, and on the day itself your technician rings when the truck pulls out. Mention the brand, the model and what the machine is doing at booking time, so likely parts ride along.

Inside, numbers come before opinions. With a heat pump or AC, our technician compares the run capacitor's microfarads to the label, inspects contactor points for pitting, takes superheat and subcooling, notes how many degrees the air cools crossing the indoor coil, and reads static pressure in the ductwork. Furnaces burning natural gas or propane get a microamp check on the flame sensor and a close look at the inducer motor and its pressure switch. For appliances, think continuity through a dryer's thermal fuse, a front-loader's drain pump and door boot, or the evaporator fan and defrost heater in a fridge that has gone warm.

Next comes a written repair price, and the call is yours. Our diagnostic visit has its own fee, named by the office before anyone is dispatched. Approve the work and that fee rides inside the repair figure as part of it; decline, and the visit costs you only that diagnostic fee. Common wear items such as run capacitors, igniters, belts, contactors, door switches, flame sensors, pumps and thermal fuses already sit in the truck bins, special-order parts show their cost before you commit, and your invoice carries the warranty terms, written out, so they outlast anyone's memory.

Twelve tabs, one for each kind of job

Each tab holds a photo from our service calls and a note on what we check first. Pick any tab; left alone, they turn every few seconds.

Digital manifold gauges hung by an outdoor unit during testing

Tab 1 of 12

Heat pump repair

Through the gray months we watch the defrost cycle closely, because a coil that never clears is the classic Kitsap winter call. Capacitors and the reversing valve come next.

See the service page
1 / 12

Can one company fix the heat pump and the washer?

It can, since one state license carries both trades. Washington lists Larch under electrical contractor license LARCHHA742PL with specialty 07D (Appliance Repair) sitting beside 06A (HVAC/Refrigeration), plus General contractor license LARCHHA745PW for installation work, and for refrigerant, every one of our technicians carries an EPA 608 Universal credential. A single stop can cover a ducted or ductless heat pump, an electric or gas furnace, an air handler, a thermostat or central air, along with the cooktop, range, oven, dishwasher, ice maker, freezer, fridge, dryer or washer.

That pairing helps where everything ages at once. Picture an early 20th-century Manette house with a gas furnace in the basement and the laundry pair a few steps away, a Silverdale subdivision where the original heat pump and the builder's fridge wear out the same year, or a family unpacking into a rental and discovering the dryer and the mini-split both need help. One booking, one set of readings, one invoice.

On the comfort side we see Mitsubishi, Daikin and Fujitsu ductless systems alongside Trane, Carrier, Bryant, Lennox, York, Goodman, Rheem and Ruud ducted gear, plus LG. In kitchens and laundry rooms it's Whirlpool, Maytag, GE, Bosch, KitchenAid, LG, Frigidaire, Electrolux, Kenmore, Speed Queen, Thermador, Wolf and Sub-Zero, and Samsung laundry pairs, dishwashers and ranges. Our license numbers are public on the state's Labor & Industries Verify search.

How do the bridges and the water shape scheduling?

Routes over here bend around bridges, and arrival windows are drawn with that in mind. The Port Washington Narrows cuts Bremerton in two: Manette and the rest of East Bremerton reach downtown and West Bremerton over the Manette Bridge, rebuilt in 2011, or the Warren Avenue Bridge carrying SR 303, built in 1958. Gig Harbor connects across the Narrows by the paired SR 16 spans, the newer one opened in 2007, while Silverdale hugs the north tip of Dyes Inlet and Poulsbo the head of Liberty Bay.

Fox Island has exactly one road link, the 1954 Fox Island Bridge over Hale Passage from Artondale, so island stops are planned around that crossing. After a storm, a closed road or a fir lying across a lane can stretch any drive, and the technician's heads-up call keeps you in the loop. When booking, add whatever shortens the last mile: a gate code, which side of the Narrows you're on, or how to spot a waterfront driveway on the island.

Our five communities

  • Bremerton98310, 98311, 98312, 98314, 98337Bremerton repair on both sides of the Port Washington Narrows: older west-side houses, Manette retrofits, rentals between tenants, and heat pumps, furnaces, mini-splits and appliances.
  • Silverdale98383, 98315Silverdale repair from Old Town on Dyes Inlet to the SR 303 corridor and hillside subdivisions, with households on the move in mind: mini-splits, furnaces, heat pumps, cooling and kitchen or laundry machines.
  • Poulsbo98370Poulsbo repair around Liberty Bay: Little Norway's downtown, the Dogfish Creek estuary, Viking Avenue, hillside subdivisions and well-fed acreage, for heat pumps, furnaces, mini-splits and appliances.
  • Gig Harbor98332, 98335, 98329Gig Harbor repair from the downtown waterfront to the uplands, Canterwood, Purdy, Rosedale, Artondale and Wollochet: salt-air condensers, zoned systems, built-in kitchens and well-fed laundry rooms.
  • Fox Island98333Fox Island repair planned around the single bridge from Artondale: salt-bitten heat pumps on waterfront and view homes, well water in appliance valves, and storm-tossed control boards.

Peninsula guides

Guide · Waterfront heat pumps

Salt air and your outdoor unit

How spray off the inlets, the harbor and Hale Passage corrodes heat pump and AC outdoor units, the safe freshwater rinse, coated coils for replacements, and when to call.

Guide · Storm season

After a windstorm outage

When firs and alders take the lines down: restarting heat pumps and furnaces safely, keeping the fridge and freezer cold, resetting a breaker once, and spotting surge damage.

Guide · Drizzle, salt spray and one bridge to the island

Heat pumps on the peninsula and islands in winter

How a heat pump copes with damp Kitsap and Fox Island winters: routine defrost versus real trouble, sideways rain, salt spray, soggy ground and fir needles, plus checks owners can make.

Guide · A moving truck and somebody else's appliances

Moving in or out: appliances and HVAC

For households changing homes around Bremerton, Silverdale and Poulsbo: washer bolts, fridge settling time, ice maker lines, dryer hookups and a heating check at the new rental.

What Kitsap homeowners ask us

Which places does Larch serve from this site?

Five communities. Bremerton, Manette, Charleston and Haddon included, on both sides of the Narrows; Silverdale, from Old Town on Dyes Inlet north along SR 3; Poulsbo, from its Liberty Bay waterfront out to the acreage beyond; Gig Harbor along with Canterwood, Purdy, Rosedale, Artondale and Wollochet; and Fox Island over Hale Passage. Sitting right at the fringe of that map? Ring the office and ask whether a route reaches your road.

Is there a charge just to find the problem?

There is. Diagnosis is billed as a visit, and the office quotes that fee during the booking call or right after an online request, well ahead of any truck leaving. Accept what the technician proposes, and the fee becomes one piece of that repair total. Pass on it, and the fee covers the trip by itself, with the written findings yours to keep.

Do you install new heat pumps and mini-splits, or only repair them?

We do both. Lots of peninsula homes that never had central air have picked up a heat pump or a ductless mini-split since the 2021 heat dome, and our 06A specialty covers installing and replacing that equipment, with the General contractor license handling the building side. Your quote lands in writing as a single figure for equipment plus installation. If the house needs new electrical service first, the quote flags it for an electrician.

Our rural home runs on propane. Can you help?

Yes, with whatever burns it inside: the furnace, the range or the dryer. Igniters, flame sensors, gas valves, inducers and pressure switches on propane units get tested the same way our technicians test natural gas equipment. The tank, its regulator and the supply piping are your propane supplier's territory, so if the fault starts there, you will hear that plainly and see it noted on the paperwork.

Someone smells gas or propane in the house. What first?

Leave right away and bring everyone with you. Once outdoors and well clear, phone 911 or the company that supplies your gas. On the way out, skip light switches, the thermostat and anything with a flame, and resist looking for the leak yourself. After the supplier or fire crew calls the house safe, our technicians can test the furnace or appliance and write up a repair price.

What warranty comes with a repair?

Your invoice spells it out, listing the terms beside the parts we fitted and the work performed, so no one has to rely on memory. Store that invoice somewhere easy to find. Should the same fault return while the terms are still in effect, phone the office with that paper close by, and a return trip gets scheduled under those terms. A phone snapshot of it suits households that relocate often.

Talk to a person

Get on the schedule from Bremerton to Fox Island

Put a date into the booking page, add the arrival window that suits you, and watch for the office's confirming call. Prefer a voice? The phone line opens at 8 AM and closes at 7 PM daily.

Schedule online

Three screens, then a confirming call

Tell us what needs attention, the day that works and the window you prefer. A scheduler calls to make it firm, and the technician rings again before pulling up.

  • Diagnostic named on the call, credited toward any repair you okay.
  • Common wear parts ride along, which often means one trip does it. Anything we must order is quoted to you first.
  • Bridges and islands are fine: add directions or gate notes in the problem box.

(360) 728-3833

Schedule a service visit

Pick the equipment, a day and a window. A scheduler calls to confirm before anything is final.

What needs a look
Day & details
Which day
Arrival window
Contact

The diagnostic charge is stated when we call and credited toward any repair you approve. We use these details only to set up the visit.

State licenses you can look up

Washington Labor & Industries keeps these records public. Each number can be searched on L&I Verify; scope details sit on a separate page.

Scope of each license
CallSchedule