Jump to main content
Bremerton · Silverdale · Poulsbo · Gig Harbor · Fox IslandLive answer daily, 8 AM until 7 PM
LarchHVAC & Appliance (360) 728-3833
Gas furnace burner compartment open for igniter service

Silverdale · Condensing gas and electric furnaces

Furnace Repair in Silverdale, WA

Silverdale heats with two very different machines: condensing gas furnaces with white PVC pipes in the newer subdivisions, and electric furnaces full of elements and sequencers in older houses and apartments. Our technicians sort out which one you have, find the part that quit, and quote the fix in writing.

  • Trip charge, then creditedExpect the diagnostic charge to be spelled out on the booking call. Green-light the fix and it is credited against the job; skip the fix and that single visit is all you owe.
  • Cost on paper, your decisionTesting pinpoints the fault, a written number follows, and nothing comes apart until you nod.
  • Coverage in writingEvery finished repair carries its warranty terms printed on your invoice.

Straight to it

Most Silverdale furnace calls trace to a flame sensor too glazed to hold its microamp signal, a cracked hot-surface igniter, a condensate trap that backs up until the pressure switch stays open, a board or fuse hurt when power returned after a storm, or a burned element or stuck sequencer in an electric unit. We pin down which, price it on paper, and repair once you agree.

What happens when we come out to repair a Silverdale furnace?

Gas furnaces in newer Silverdale homes log recent faults on the control board, and that blink code shows whether startup stalled at the inducer, the pressure switch, the igniter or flame proving. Then the meter settles it: igniter ohms, flame current in microamps with burners lit, the switch's closing point in inches of water column, and transformer output. Electric furnaces get a separate routine, with each element, sequencer and limit measured and supply air compared with return air.

Every visit opens with a diagnostic charge, its amount stated by the office at booking. Approve the work and it merges into the repair bill; decline, and that charge is the whole of it. The technician writes out the repair figure and waits for your okay before unbolting anything, and warranty terms land on the invoice. Igniters, flame sensors, blower motors and condensate pumps ride in the truck. Larch carries the Washington 06A HVAC/Refrigeration specialty.

Which furnace problems turn up most in Silverdale?

  • Burners light, then shut off within a few seconds

    What it usually is
    A flame sensor coated in oxide or dust carries too little current back to the board, which then closes the gas valve as a precaution.
    What the technician does
    We read the flame current in microamps, polish or replace the rod, and confirm the burner ground so the signal holds all season.
  • Inducer starts, but there is no orange glow and no flame

    What it usually is
    The hot-surface igniter has cracked or burned open, a common end for a part that cycles many times a day through a long heating season.
    What the technician does
    We check igniter ohms and the voltage reaching it, fit a matching igniter from truck stock, and watch several complete starts.
  • High-efficiency furnace gurgles and flashes a pressure switch code

    What it usually is
    Sludge in the condensate trap or a sagging drain hose pools water in the collector box, so the switch never proves draft.
    What the technician does
    We empty and rinse the trap, blow out the drain and switch tubing, and re-hang the hose so it slopes steadily to the pump.
  • Furnace stays dead after the power comes back on

    What it usually is
    The surge at restoration can open the board's low-voltage fuse, damage the transformer, or leave the board locked out after repeated failed starts.
    What the technician does
    We pull the stored codes, measure transformer output and the fuse, check the door safety switch, and replace a board only when readings call for it.
  • Electric furnace in an older home or apartment blows lukewarm air

    What it usually is
    One element coil has opened, a sequencer has quit staging the next element in, or a tired limit trips early because the filter is packed.
    What the technician does
    Each element and sequencer gets an ohm and amp reading, supply and return temperatures are compared, and we look at blower speed so new parts last.

How do Silverdale subdivisions, storms and moves affect furnaces?

Most gas furnaces in Silverdale's newer subdivisions are condensing models that breathe through two white PVC pipes, often out a sidewall near the ground. Wet winters at the head of Dyes Inlet keep them running for hours a day, which keeps water moving through the trap and gives algae a home. Keep both pipe ends clear of leaves, fir needles, bark mulch and stacked firewood. A blocked end stops the pressure switch from closing, and the burners never get the go-ahead.

Windstorms are the other Silverdale pattern. In the November 2024 bomb cyclone, downed trees and lines closed 22 roads across Kitsap County, and long outages end in cold restarts. Once power is back, give the furnace a few minutes, see whether the thermostat schedule survived, and flip a tripped breaker on a single time. Families who just moved in often inherit a furnace they have never seen. One rule for every household: if gas is in the air, everyone leaves first, 911 or the gas utility gets the call from outside, and we come once they say the house is safe.

Twelve tabs, one for each kind of job

Each tab holds a photo from our service calls and a note on what we check first. Pick any tab; left alone, they turn every few seconds.

Technician beside a furnace in a utility closet

Tab 1 of 12

Furnace repair

Many older Bremerton and Manette houses keep the furnace in a closet or under the floor. Filter, inducer, flame sensor and limit switch all get checked in that tight space.

See the service page
1 / 12

Where do these furnace issues show up around Silverdale?

Old Town Silverdale

Old Town sits on the water at the top of Dyes Inlet, and its older houses often rely on electric resistance furnaces or gas units well past middle age. Damp inlet air rusts cabinet screws and blower housings. We check elements, sequencers and wire terminals first, since connections loosen after many winters of heat.

Newer subdivisions

Homes in Silverdale's newer subdivisions lean on condensing gas furnaces set in garages or utility closets. Each depends on a clean trap, a drain line with steady fall, and sometimes a small condensate pump. We clear the trap and line, test the pump's float, and look over both PVC terminations before closing up.

Apartments near SR 303

Apartments along the SR 303 and SR 3 commercial corridor often heat with compact electric furnaces or air handlers squeezed into a hallway closet. Tight closets starve the return, and a clogged filter lets the limit cut elements in and out. Show us the closet and filter slot, and we measure each element before quoting.

What Kitsap homeowners ask us

How long should we wait for the furnace after the power comes back?

A few minutes is normally enough. Many gas furnaces run a self-check and an inducer purge before trying to light, and a thermostat without batteries may lose its schedule. If ten minutes pass with no sign of life, reset the furnace breaker once and make sure the front panel presses its door switch, then schedule us to meter the board and transformer.

Why is there water around our furnace when it runs?

On a condensing furnace, water is expected, but it belongs in the drain. These units pull so much heat from the exhaust that moisture condenses inside and flows through a trap to a drain or small pump. A split trap, a PVC fitting that worked loose, or a pump with a stuck float spills it on the floor instead. Switch the furnace off at the thermostat and book a repair.

Can we clean the flame sensor ourselves?

We suggest leaving it to a technician. The rod sits beside the burners and gas valve, removing it disturbs the safety circuit, and a quick polish does not show whether the signal will hold. Our technicians read the microamps before and after, and swap the rod when cleaning does not bring the number back. A furnace that lights and drops out is pointing at that sensor.

Our apartment has an electric furnace. Is that something you repair?

Yes. Electric furnaces are common in Silverdale's older houses and many apartments, and their failures differ from gas units: elements burn open, sequencers stick, limit switches weaken, and terminals darken from years of heat. We test each piece and compare supply and return temperatures to prove the repair worked. If the furnace breaker trips again right after one reset, leave it off and call.

Talk to a person

Book Silverdale furnace repair

Silverdale households can lock in a visit two ways. Online, the calendar shows open days and arrival windows; by phone, the office picks up daily between 8 AM and 7 PM. Confirmation comes as a quick call, and the technician dials you when departing.

Schedule online

Three screens, then a confirming call

Tell us what needs attention, the day that works and the window you prefer. A scheduler calls to make it firm, and the technician rings again before pulling up.

  • Diagnostic named on the call, credited toward any repair you okay.
  • Common wear parts ride along, which often means one trip does it. Anything we must order is quoted to you first.
  • Bridges and islands are fine: add directions or gate notes in the problem box.

(360) 728-3833

Schedule a service visit

Pick the equipment, a day and a window. A scheduler calls to confirm before anything is final.

What needs a look
Day & details
Which day
Arrival window
Contact

The diagnostic charge is stated when we call and credited toward any repair you approve. We use these details only to set up the visit.

State licenses you can look up

Washington Labor & Industries keeps these records public. Each number can be searched on L&I Verify; scope details sit on a separate page.

Scope of each license
CallSchedule